-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Material Witness: The Use of Fillers in Composites
August 3, 2015 | Chet GuilesEstimated reading time: 4 minutes
The use of finely divided ceramic fillers in composites intended for use in printed wiring boards has a long history, but most people still associate the idea with reducing the cost of the product by loading it with an inexpensive inert filler. Nothing could be further from the truth. The use of fillers provides the resin formulator with an opportunity to adjust and improve many of the important properties of a resin system. Just a few of the benefits of using a controlled level of micro-disperse ceramic additives include:
- Reduction of shrinkage of resin during cure
- Improvement of drilling quality
- Reduction in registration irregularity
- Increased thermal conductivity
- Improvement in coating quality
- Minimization of formation and propagation of cracks
- Reduction in overall Z-direction expansion
- Modification of electrical properties
Thermosetting resin systems such as those used in PWB laminates and prepregs tend to shrink volumetrically by as much as 4% on curing, due to the formation of regular structures and cross-links. In a laminate structure this creates some built-in stresses, as the shrinking resin is held in place by the glass reinforcement and by copper foil on the surface. When copper is subsequently etched away, the resin tends to relieve stresses to the extent that it can, resulting in some dimensional change in the material that can cause misregistration, warpage and other undesirable phenomena. The use of fillers can mitigate this post-etch shrinkage and make registration more controllable and predictable.
Talc has been used in PWB laminate systems since the 1950s to improve drilling quality, especially in older epoxy systems which have a tendency to smear when being drilled. The soft, platy talc both acts to lubricate at the drill cutting edge and to break up the chip from the material, reducing heat build-up and subsequent smearing. Other fillers also may improve drilling quality and reduce fracturing of the resin at drilled holes, reducing wicking and other anomalies that cause concern during wet process and plating.
Fillers may also be used to boost the thermal conductivity of a resin system. Fillers such as hydrated alumina and boron nitride have high thermal coefficients of heat transfer. Highly filled laminate composites can have Tc values as high as 1-2 W/m-K compared to 0.2- 0.3 W/m-K for unfilled glass-reinforced products.
Cracking of resin during drilling or handling can be significantly reduced by the dispersion of a finely divided filler in the resin system. A crack (which you can picture as a conic section “drilling” into the resin) develops extremes of force at the very tip; as the radius of the cone approaches zero, the force per unit area goes very high. Pressure = Force/Area. When area approaches zero as a limit, the pressure theoretically goes to infinity. What a filler does is to intercept the crack and dramatically increase the effective surface area, resulting in a reduced pressure and stopping the crack from propagating. Figure 1 illustrates this phenomenon.
In structural composites, crack propagation is often controlled by the inclusion of a discrete second phase in the system consisting of particles of a synthetic rubber such as Shell’s Kraton® which serve the same function as we achieve using ceramic fillers in PWB laminates and prepregs.
Crack initiation may be caused by drilling and handling. Radial cracking is often seen when drilling a large clearance hole in a resin-rich area, where resin shrinkage has created built-in stresses. In such cases the filler serves a dual purpose—both to reduce the shrinkage and to help eliminate the formation and propagation of cracks.
Opposite the shrinkage and related phenomena, fillers also tend to reduce the thermal expansion of the material. Most resins expand in the range of 40-50 ppm/oC, resulting in both in-plane and vertical expansion when a PWB is heated either in service or during processes such as solder leveling and reflow. Fillers reduce the resin expansion in all dimensions, but especially the Z-direction. When resins expand they do so isotropically unless restrained (the same in all directions) and are incompressible. The glass fabric in most laminates restrains the X-Y movement and so the resin moves in the Z-direction. That’s why most laminates have XY CTEs of 16-17 ppm/oC and Z-direction CTEs of 50-60 ppm/oC. Filled resins expand less and hence have reduced expansion in all directions.
Finally, we can consider the effect that fillers may have on electrical properties. Several considerations are important.
First, fillers have to be “clean” and free of ionic contaminants that might result in reduced ability to withstand voltage loading. Most laminate specifications want a minimum of 750 volts per mil of resistance to dielectric breakdown, and a “dirty” filler can reduce that substantially.
Second, fillers must have electrical properties that are desirable for the application. Commonly used is pure silica (SiO2) because it has a low dielectric constant as well as a low coefficient of thermal expansion. Combined with nonpolar resin systems, low controlled dielectric constants are possible in cost-effective systems for microwave and RF applications requiring Dk of 3.5 or less and loss values of 0.002-0.004.
The bottom line: Fillers are not simply dumped into a resin system to cheapen it, but they are usually engineered and tightly controlled to modify and improve specific properties that are of interest to the designer and user of PWBs.
For now, this is the Material Witness wishing you a happy summer.
Suggested Items
Indium Corporation to Present, Exhibit at EPP InnovationsFORUM
03/28/2024 | Indium CorporationIndium Corporation is set to present and exhibit at EPP InnovationsFORUM, one of Europe’s premier single-day electronics manufacturing forums, on April 17 in Leinfelden-Echterdingen, Germany. Topic areas for 2024 will include AI, automation, sustainability, and quality.
Reducing Nitrogen Consumption in Convection Soldering with Rehm Thermal Systems' Patented Mechatronic Curtain
03/28/2024 | Rehm Thermal SystemsCurrent developments indicate a need for larger throughput heights due to the trend towards e-mobility, which in turn increases nitrogen consumption for process inertization. Rehm Thermal Systems responds to this issue with an innovative solution: the mechatronic curtain.
Indium Corporation, Industry Partners to Showcase Products “Live@APEX”
03/26/2024 | Indium CorporationIndium Corporation®, in cooperation with its industry partners, will feature its proven solder solutions live on the show floor throughout IPC APEX Expo from Apr. 9‒11 in Anaheim, Calif., U.S.
ITW EAE Wins New Product Introduction Award for Electrovert® Wave Soldering Machine Deep Wave
03/26/2024 | ITW EAEITW EAE is proud to announce that it has earned a 2024 New Product Introduction (NPI) Award for Electrovert’s Deep Wave option for wave soldering machines. This new, innovative system provides the ability to pump up to a 20 mm wave height.
Mek's Next-Gen AOI Technology Takes Center Stage at IPC APEX EXPO 2024
03/19/2024 | MEKMek is excited to announce its presence at IPC APEX EXPO, North America's largest electronics manufacturing event, in Anaheim, California, from April 6-11, 2024. Attendees are invited to visit Mek at booth #1433 to explore the latest AOI technology offerings.