Companies Maximize 300mm, 200mm Wafers; Slow Progress on 450mm
September 15, 2015 | IC InsightsEstimated reading time: 2 minutes
Larger wafer diameters provide more chips per wafer at a modest increase in material and process costs, resulting in reduced chip costs. Historically, transitions to larger diameter wafers have provided cost reductions greater than 20% per unit area. However, enormous financial and technology hurdles continue to plague the development of, and the transition to, 450mm wafers. As a result, the transition to larger diameter wafer has slowed dramatically and companies are maximizing their efficiency using 300mm and 200mm wafers. IC Insights’ Global Wafer Capacity 2015-2019 report shows that worldwide capacity by wafer size was dominated by 300mm wafers in 2014 and is forecast to continue increasing through 2019.
Efforts to develop 450mm wafer technology continue to make some progress, but the pace of development slowed significantly in 2014. Now, by most accounts, volume production using 450mm wafers is not expected before 2020, although pilot production could start a year or two before. IC Insights shows 450mm wafers accounting for a very slim share of installed capacity in 2019.
For the most part, 300mm fabs are, and will continue to be, limited to production of high-volume, commodity-type devices like DRAMs and flash memories; image sensors and power management devices; and complex logic and microcomponent ICs with large die sizes; and by foundries, which can fill a 300mm fab by combining wafer orders from many sources.
At the end of 2014, there were 87 production-class IC fabs utilizing 300mm wafers. There are several 300mm R&D IC fabs and a few high-volume 300mm fabs around the world that make “non-IC” products such as image sensors and discretes, but these are not included in the count shown in the chart.
Only once—in 2013—has the number of 300mm wafer fabs declined. That year, three large fabs operated by ProMOS and Powerchip closed and setbacks delayed the opening of several new 300mm fabs until 2014. By the end of 2019, there are expected to be 23 more 300mm wafer fabs in operation than there were at the close of 2014. The number of 300mm fabs will likely peak between 115-120, which assumes 450mm fabs will enter volume production in the future. For comparison, the greatest number of volume-production 200mm wafer fabs in operation was 210 (the number declined to 154 fabs at the end of 2014).
The list of companies with the most 300mm wafer capacity includes memory suppliers Samsung, Micron, SK Hynix, and Toshiba/SanDisk; the industry’s biggest IC manufacturer and dominant MPU supplier Intel; and the world’s two largest pure-play foundries TSMC and GlobalFoundries. These companies offer the types of ICs that benefit most from using the largest wafer size available to best amortize the manufacturing cost per die.
The number of fabs running 200mm wafers will continue to be profitable for many more years and be used to fabricate numerous types of ICs including specialty memories, display drivers, microcontrollers, analog products, and MEMS-based devices. Devices like these are practical to make in fully depreciated 200mm fabs that were used to produce devices now made on 300mm wafers. TSMC, TI, and UMC remain the three companies with the greatest amount of 200mm wafer fab capacity.
Suggested Items
Growth Potential: Electronics Manufacturing Driving Massive Surge in Manufacturing Investment
04/22/2024 | Shawn DuBravac, IPCIn the early months of the pandemic, investment in manufacturing infrastructure, such as plants and production facilities, declined sharply. Real investment dropped over 11%, before finally recovering to pre-pandemic levels in the first half of 2022. Over the past two years, however, several factors have combined to drive manufacturing investment to record levels.
ViTrox Pioneering the Future of Smart Manufacturing at NEPCON China 2024
04/18/2024 | ViTroxViTrox, which aims to be the World’s Most Trusted Technology Company, is pleased to announce its participation in the NEPCON China 2024 at Booth #1H27 at Shanghai World Expo Exhibition & Convention Center from 24-26 April 2024.
Renesas Commences Operations of Kofu Factory as Dedicated 300-mm Wafer Fab for Power Semiconductors
04/15/2024 | RenesasRenesas Electronics Corporation, a premier supplier of advanced semiconductor solutions, today announced that it has started operations at its Kofu Factory, located in Kai City, Yamanashi Prefecture, Japan.
Aegis Software and JUKI Extend Reseller Relationship, Marking Over 23 Years of Collaboration
04/11/2024 | Aegis SoftwareAegis Software, a global provider of Manufacturing Execution System (MES) software, announces that JUKI Automation, a world-leading provider of automated assembly products and systems and subsidiary of JUKI Corporation, has renewed their reseller relationship with Aegis Software.
TT Electronics Awarded Contract with Kongsberg Defence and Aerospace
04/11/2024 | TT ElectronicsTT Electronics, a leading provider of global manufacturing solutions and engineered technologies, announced today that its Fairford UK business has been awarded a new contract with long-standing customer Kongsberg Defence and Aerospace (Kongsberg) for the production of complex cable harness solutions.